Stima V3.12

What's Changed

• i2c-radiation and i2c-wind redesign
• bugs in i2c-rain: after a print inside ISR interrupt on pin do not work any more and others
• sensor_config migrated to sensor_config_menu_sdcard, a full tool to configure sensor and i2c modules; it use LCD and encoder
  but can be used by serial port and IR remote; all module accept confihuration by i2c
• digitecoboot with different MCU clock
• changed windsonic output rate from 4 to 2 /sec
• added i2c-power
• severe BUG in getSDFromUV for i2c-wind
• added SHT driver to SensorDriver (ported from SendorDriverb)
• no watchdog when i2c is broken in stima
• change default ADC max input voltage from 2.048V to 6.144V (the defau…
• auto tune ADC gain in i2c-radiation
• stima v3 read binary configuration from CDcard
• new sensor_config with master binary configuration read from SDcard
• stima v3 station configuration by i2c with sensor_config_menu_sdcard
• added SD formatter to sensor_config_menu_sdcard
• stima v3 station configuration by i2c with sensor_config_menu_sdcard

Stima 3.10

What's Changed

• change stima configuration for more sensors and more complex sensors ike station with wind and radiation require
• close #428 : commit
• close #429 : commit
• close #430 : commit
• close #431 : commit

Stima

What's Changed

• permit configuration with all disconnected at boot
• close #424
• close #425
• added firmware major and minor version to mqtt connect payload

Stima

What's Changed

• bug for infinite loop with NTP error
• better messages on LCD display
• migrate authentication from user to user/station_slug/board_slug
• migrate to RMAP over MQTT v1

Full Changelog: 3.7.6...3.8.1

Stima

What's Changed

• manage transaction on i2c commands by @pat1 in #418
• close #419 by @pat1 in #420

Full Changelog: 3.7.5...3.7.6

Stima

Issue closed:

• close #416

Full Changelog: 3.7.4...3.7.5

Stima

Changes:

• bug in digitecopower Sensordriver driver
• better timing for i2c-th Sensordriver driver (required when logging on SDcard is activated)
• better command execution in i2c-th without conflict with interrupt of timer1
• other minor bugs in Stima firmware

Stima

Principali modifiche:

• In i2c-th elaborare la prima osservazione su 14 campionamenti e tutti le successive su 15 avendo così un anticipo fisso di 4 secondi più che sufficienti allo scopo di sincromizzarsi con il master
• migliorata visualizzazione su display
• riscritto driver per digitecopower in SensorDriver
• ripulito i2c-rain e nuova versione di configurazione

Stima

Principali cambiamenti:

• make sure reading old and invalid data are not possible;corrected wrong timing in SensorDriver library
• adjust timing and wdt for logging on SDcard

Stima

Principali modifiche:

• reinizializzazione SDcard in caso di errore (bug)
• risolti altri bug minori
• parzialmente riscritto i2c-th: ora la configurazione dei sensori si effettua non a tempo di compilazione ma tramite sensor-config; il tempo di elaborazione dei report non è definito a tempo di compilazione ma definito dai comandi impartiti dal master; risolti alcuni problemi tra cui #400
• rivista la gestione di digiteco_power in SensorDriver
• migliorata la gestione dei dati mancanti
• migliorata la libreria Wire per la gestione I2C; alcuni parametri di configurazione non erano presi in considerazione e sono stati migrati a platform.io
• aggiunto file di info con alcuni metadati: ora la lunghezza record dei dati salvati può essere variata senza creare problemi al lettore python
• aggiornato librerie: ArduinoJson, PubSubClient