ESP8266_AT_WebServer

---

---

Table of Contents

• Important Note from v1.6.0
• Why do we need this ESP8266_AT_WebServer library
  • Features
  • Currently Supported Boards
  • Currently Supported AT-command shields
• Changelog
• Prerequisites
• Important Notes about AT Firmwares
  • 1. Tested OK with ESP8266-AT shields
  • 2. Tested OK with ESP32-AT shields
  • 3. Where to upload AT-Firmware
  • 4. Important Notes
• Installation
  • Use Arduino Library Manager
  • Manual Install
  • VS Code & PlatformIO
• Packages' Patches
  • 1. For Adafruit nRF52840 and nRF52832 boards
  • 2. For Teensy boards
  • 3. For Arduino SAM DUE boards
  • 4. For Arduino SAMD boards
    • For core version v1.8.10+
    • For core version v1.8.9-
  • 5. For Adafruit SAMD boards
  • 6. For Seeeduino SAMD boards
  • 7. For STM32 boards
    • 7.1. For STM32 boards to use LAN8720
    • 7.2. For STM32 boards to use Serial1
  • 8. For RP2040-based boards using Earle Philhower arduino-pico core
    • 8.1. To use BOARD_NAME
    • 8.2. To avoid compile error relating to microsecondsToClockCycles
  • 9. For Portenta_H7 boards using Arduino IDE in Linux
  • 10. For RTL8720DN boards using AmebaD core
  • 11. For SAMD21 and SAMD51 boards using ArduinoCore-fab-sam core
  • 12. For Seeeduino RP2040 boards
  • 13. For Seeeduino nRF52840 boards
• Usage
  • Class Constructor
  • Basic Operations
  • Advanced Options
  • Other Function Calls
• Examples
  • 1. AdvancedWebServer
  • 2. AdvancedWebServer_STM32
  • 3. ConnectWPA
  • 4. HelloServer
  • 5. HelloServer2
  • 6. HttpBasicAuth
  • 7. MQTTClient_Auth
  • 8. MQTTClient_Basic
  • 9. MQTT_ThingStream
  • 10. PostServer
  • 11. ScanNetworks
  • 12. SimpleAuthentication
  • 13. UdpNTPClient
  • 14. UdpSendReceive
  • 15. WebClient
  • 16. WebClientRepeating
  • 17. WebServer
  • 18. WebServerAP
  • 19. ATWebServer_BigData New
• Example AdvancedWebServer
  • 1. File AdvancedWebServer.ino
  • 2. File defines.h
• Debug Terminal Output Samples
  • 1. AdvancedWebServer on Adafruit NRF52840_ITSYBITSY_EXPRESS using ESP8266-AT shield
  • 2. MQTT_ThingStream on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield
  • 3. MQTTClient_Auth on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield
  • 4. MQTTClient_Basic on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield
  • 5. WebClientRepeating on RASPBERRY_PI_PICO using ESP8266-AT shield
  • 6. MQTTClient_Auth on RASPBERRY_PI_PICO using ESP8266-AT shield
  • 7. UdpNTPClient on MBED RASPBERRY_PI_PICO using ESP8266-AT shield
  • 8. AdvancedWebServer on NRF52840_ITSYBITSY
  • 9. ATWebServer_BigData on NRF52840_ITSYBITSY
  • 10. AdvancedWebServer on WIZNET_WIZFI360_EVB_PICO
• Screen Shots
  • 1. SAMD51 Itsy-Bitsy M4
  • 2. STM32 Nucleo-144 NUCLEO_F767ZI
  • 3. nRF52 Itsy-Bitsy nRF52840
  • 4. Seeeduino SEEED_XIAO_M0
  • 5. RASPBERRY_PI_PICO
  • 6. MBED RASPBERRY_PI_PICO
  • 7. nRF52 Itsy-Bitsy nRF52840 BigData
• Debug
• Troubleshooting
• Issues
• TO DO
• DONE
• Contributions and Thanks
• Contributing
• License
• Copyright

---

---

Important Note from v1.6.0

The new ESP8266_AT_WebServer v1.7.1+ fixes severe limitation to permit sending much larger data than total than 2K buffer of ESP8266/ESP32 AT-command shield.

---

---

Why do we need this ESP8266_AT_WebServer library

Features

This ESP8266_AT_WebServer library is a simple yet complete WebServer library for AVR, Teensy, SAM DUE, Arduino SAMD21, Adafruit SAMD21/SAMD51, Adafruit nRF52, STM32F/L/H/G/WB/MP1, etc. boards, using ESP8266/ESP32 AT-command WiFi modules/shields.

The functions are similar and compatible to those of ESP32 WebServer and ESP8266WebServer libraries to make life much easier to port sketches from ESP8266/ESP32.

The library provides supports to:

1. WiFi Client, STA and AP mode
2. TCP Server and Client
3. UDP Server and Client
4. HTTP Server and Client
5. HTTP GET and POST requests, provides argument parsing, handles one client at a time.
6. UDP Multicast and Broadcast.

It is based on and modified from:

1. Ivan Grokhotkov's ESP8266WebServer
2. bportaluri's WiFiEsp library

The ESP8266_AT_Web_Server class found in ESP8266_AT_Web_Server.h header, is a simple web server that knows how to handle HTTP requests such as GET and POST and can only support one simultaneous client.

Currently Supported Boards

1. nRF52 boards, such as AdaFruit Feather nRF52832, nRF52840 Express, BlueFruit Sense, Itsy-Bitsy nRF52840 Express, Metro nRF52840 Express, NINA_B302_ublox, NINA_B112_ublox, etc.

2. SAM DUE

3. SAMD21

• Arduino SAMD21: ZERO, MKRs, NANO_33_IOT, etc.
• Adafruit SAMD21 (M0): ItsyBitsy M0, Feather M0, Feather M0 Express, Metro M0 Express, Circuit Playground Express, Trinket M0, PIRkey, Hallowing M0, Crickit M0, etc.
• Seeeduino: LoRaWAN, Zero, Femto M0, XIAO M0, Wio GPS Board, etc.

4. SAMD51

• Adafruit SAMD51 (M4): Metro M4, Grand Central M4, ItsyBitsy M4, Feather M4 Express, Trellis M4, Metro M4 AirLift Lite, MONSTER M4SK Express, Hallowing M4, etc.
• Seeeduino: Wio Terminal, Grove UI Wireless

5. Teensy (4.1, 4.0, 3.6, 3.5, 3,2, 3.1, 3.0, LC)

6. STM32F/L/H/G/WB/MP1 boards (with 64+K Flash)

• Nucleo-144
• Nucleo-64
• Discovery
• Generic STM32F0, STM32F1, STM32F2, STM32F3, STM32F4, STM32F7 (with 64+K Flash): x8 and up
• STM32L0, STM32L1, STM32L4, STM32L5
• STM32G0, STM32G4
• STM32H7
• STM32WB
• STM32MP1
• LoRa boards
• 3-D printer boards
• Generic Flight Controllers
• Midatronics boards

7. SIPEED_MAIX_DUINO boards

8. RP2040-based boards, such as Nano RP2040 Connect, using Arduino mbed OS for Nano boards.

9. RP2040-based boards, such as RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040 and GENERIC_RP2040, using Arduino-mbed RP2040 core or Earle Philhower's arduino-pico core.

10. WIZNET_WIZFI360_EVB_PICO using Earle Philhower's arduino-pico core

WIZNET_WIZFI360_EVB_PICO

---

Currently Supported AT-command shields

1. ESP8266-AT-command shield
2. ESP32-AT-command shield
3. W600 and WIS600-01S AT-command shield
4. WizFi360 AT-command shield

WIZFI360

---

---

Prerequisites

1. Arduino IDE 1.8.19+ for Arduino.
2. Arduino AVR core 1.8.6+ for Arduino (Use Arduino Board Manager) for AVR boards.
3. Teensy core v1.57+ for Teensy 4.1.
4. Arduino SAM DUE core v1.6.12+ for SAM DUE ARM Cortex-M3 boards.
5. Arduino SAMD core 1.8.13+ for SAMD ARM Cortex-M0+ boards.
6. Adafruit SAMD core 1.7.11+ for SAMD ARM Cortex-M0+ and M4 boards (Nano 33 IoT, etc.).
7. Seeeduino SAMD core 1.8.3+ for SAMD21/SAMD51 boards (XIAO M0, Wio Terminal, etc.).
8. Adafruit nRF52 v1.3.0+ for nRF52 boards such as Adafruit NRF52840_FEATHER, NRF52832_FEATHER, NRF52840_FEATHER_SENSE, NRF52840_ITSYBITSY, NRF52840_CIRCUITPLAY, NRF52840_CLUE, NRF52840_METRO, NRF52840_PCA10056, PARTICLE_XENON, NINA_B302_ublox, etc. . Please remember to use latest Packages_Patches or getting compiler errors.
9. Arduino Core for STM32 v2.4.0+ for STM32F/L/H/G/WB/MP1 boards.
10. Arduino mbed_rp2040 core 3.5.4+ for Arduino (Use Arduino Board Manager) RP2040-based boards, such as Arduino Nano RP2040 Connect, RASPBERRY_PI_PICO, etc..
11. Earle Philhower's arduino-pico core v2.7.1+ for RP2040-based boards such as RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040 and GENERIC_RP2040, etc.
12. Sipeed Maixduino core v0.3.11+ for K210-RISC-V-based boards such as Maixduino AI Development Kit K210 RISC-V AI + IoT ESP32, Sipeed Maix Go, Sipeed Maix Bit, etc.
13. Functional-Vlpp library v1.0.2+ to use server's lambda function. To install. check
14. Ai-Thinker AT Firmware v1.5.4 or AT Firmware v1.7.4.0 for ESP8266-AT shields.
15. AT version_2.1.0.0_dev for ESP32-AT shields.
16. AT version_1.1.4 for WIS600-01S and W600-AT WiFi shields
17. AT version 3.2.0 for WizFi360 WiFi shields

---

---

Important Notes about AT Firmwares

1. Tested OK with ESP8266-AT shields

• Ai-Thinker AT Firmware v1.5.4

  AT version:1.1.0.0(May 11 2016 18:09:56)
  SDK version:1.5.4(baaeaebb)
  Ai-Thinker Technology Co. Ltd.
  Jun 13 2016 11:29:20

• AT Firmware v1.7.4.0

  AT version:1.7.4.0(May 11 2020 19:13:04)
  SDK version:3.0.4(9532ceb)
  compile time:May 27 2020 10:12:17
  Bin version(Wroom 02):1.7.4

• WIS600-01S and W600 using either ESP8266 or ESP32-AT commands and stock firmware

  AT version:1.1.4(Dec 05 2018 11:06:45)
  SDK version:3.0.0
  Dec 05 2018 11:06:45

2. Tested OK with ESP32-AT shields

• AT version_2.1.0.0_dev

  AT version:2.1.0.0-dev(4f6b92c - Jun 10 2020 10:36:54)
  SDK version:v4.0.1-193-ge7ac221b4
  compile time(b85a8df):Jun 18 2020 14:00:59
  Bin version:2.0.0(WROOM-32)

  See instructions at AT Command Core and ESP_AT_Get_Started

3. Where to upload AT-Firmware

Upload AT Firmware v1.7.4.0 bin files to correct locations as follows:

# BOOT MODE

### Flash size 8Mbit: 512KB+512KB
    boot_v1.2+.bin              0x00000
    user1.1024.new.2.bin        0x01000
    esp_init_data_default.bin   0xfc000
    blank.bin                   0x7e000 & 0xfe000


### Flash size 16Mbit-C1: 1024KB+1024KB
    boot_v1.2+.bin              0x00000
    user1.2048.new.5.bin        0x01000
    esp_init_data_default.bin   0x1fc000
    blank.bin                   0xfe000 & 0x1fe000

4. Important Notes

• Test before using different AT-Firmware Version at your own risks. Just use any simple example to verify if the AT-firmware is OK.

• Compatible AT-Firmare version will be updated. Check for all supported AT Firmwares and download them from AT_Firmwares.

• Support to ESP32-AT-command shields has been added to permit using new library ESP_AT_Lib to replace Blynk's BlynkESP8266_Lib. The same ESP_AT_Lib can also be use for ESP8266-AT shields.

---

---

Installation

Use Arduino Library Manager

The best and easiest way is to use Arduino Library Manager. Search for ESP8266_AT_Web_Server, then select / install the latest version. You can also use this link for more detailed instructions.

Manual Install

1. Navigate to ESP8266_AT_WebServer page.
2. Download the latest release ESP8266_AT_WebServer-master.zip.
3. Extract the zip file to ESP8266_AT_WebServer-master directory
4. Copy whole

• ESP8266_AT_WebServer-master folder to Arduino libraries' directory such as ~/Arduino/libraries/.

VS Code & PlatformIO:

1. Install VS Code
2. Install PlatformIO
3. Install ESP8266_AT_WebServer library by using Library Manager. Search for ESP8266_AT_WebServer in Platform.io Author's Libraries
4. Use included platformio.ini file from examples to ensure that all dependent libraries will installed automatically. Please visit documentation for the other options and examples at Project Configuration File

---

---

Packages' Patches

1. For Adafruit nRF52840 and nRF52832 boards

To be able to compile, run and automatically detect and display BOARD_NAME on nRF52840/nRF52832 boards, you have to copy the whole nRF52 Packages_Patches directory into Adafruit nRF52 directory (~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0).

Supposing the Adafruit nRF52 version is 1.3.0. These files must be copied into the directory:

• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/platform.txt
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/boards.txt
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/cores/nRF5/Udp.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/cores/nRF5/Print.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/cores/nRF5/Print.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/variants/NINA_B302_ublox/variant.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/variants/NINA_B302_ublox/variant.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/variants/NINA_B112_ublox/variant.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/variants/NINA_B112_ublox/variant.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/1.3.0/cores/nRF5/Udp.h

Whenever a new version is installed, remember to copy these files into the new version directory. For example, new version is x.yy.z These files must be copied into the directory:

• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/platform.txt
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/boards.txt
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/cores/nRF5/Udp.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/cores/nRF5/Print.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/cores/nRF5/Print.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/variants/NINA_B302_ublox/variant.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/variants/NINA_B302_ublox/variant.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/variants/NINA_B112_ublox/variant.h
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/variants/NINA_B112_ublox/variant.cpp
• ~/.arduino15/packages/adafruit/hardware/nrf52/x.yy.z/cores/nRF5/Udp.h

2. For Teensy boards

To be able to compile and run on Teensy boards, you have to copy the files in Packages_Patches for Teensy directory into Teensy hardware directory (./arduino-1.8.19/hardware/teensy/avr/boards.txt).

Supposing the Arduino version is 1.8.19. These files must be copied into the directory:

• ./arduino-1.8.19/hardware/teensy/avr/boards.txt
• ./arduino-1.8.19/hardware/teensy/avr/cores/teensy/Stream.h
• ./arduino-1.8.19/hardware/teensy/avr/cores/teensy3/Stream.h
• ./arduino-1.8.19/hardware/teensy/avr/cores/teensy4/Stream.h

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz These files must be copied into the directory:

• ./arduino-x.yy.zz/hardware/teensy/avr/boards.txt
• ./arduino-x.yy.zz/hardware/teensy/avr/cores/teensy/Stream.h
• ./arduino-x.yy.zz/hardware/teensy/avr/cores/teensy3/Stream.h
• ./arduino-x.yy.zz/hardware/teensy/avr/cores/teensy4/Stream.h

3. For Arduino SAM DUE boards

To be able to compile and run on SAM DUE boards, you have to copy the whole SAM DUE directory into Arduino sam directory (~/.arduino15/packages/arduino/hardware/sam/1.6.12).

Supposing the Arduino SAM core version is 1.6.12. This file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/sam/1.6.12/platform.txt

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/sam/x.yy.zz/platform.txt

4. For Arduino SAMD boards

To be able to compile, run and automatically detect and display BOARD_NAME on Arduino SAMD (Nano-33-IoT, etc) boards, you have to copy the whole Arduino SAMD Packages_Patches directory into Arduino SAMD directory (~/.arduino15/packages/arduino/hardware/samd/1.8.13).

For core version v1.8.10+

Supposing the Arduino SAMD version is 1.8.13. Now only one file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/samd/1.8.13/platform.txt

Whenever a new version is installed, remember to copy this files into the new version directory. For example, new version is x.yy.zz

This file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/samd/x.yy.zz/platform.txt

For core version v1.8.9-

Supposing the Arduino SAMD version is 1.8.9. These files must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/samd/1.8.9/platform.txt
• ~/.arduino15/packages/arduino/hardware/samd/1.8.9/cores/arduino/Arduino.h

Whenever a new version is installed, remember to copy these files into the new version directory. For example, new version is x.yy.z

These files must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/samd/x.yy.z/platform.txt
• ~/.arduino15/packages/arduino/hardware/samd/x.yy.z/cores/arduino/Arduino.h

This is mandatory to fix the notorious Arduino SAMD compiler error. See Improve Arduino compatibility with the STL (min and max macro)

 ...\arm-none-eabi\include\c++\7.2.1\bits\stl_algobase.h:243:56: error: macro "min" passed 3 arguments, but takes just 2
     min(const _Tp& __a, const _Tp& __b, _Compare __comp)

Whenever the above-mentioned compiler error issue is fixed with the new Arduino SAMD release, you don't need to copy the Arduino.h file anymore.

5. For Adafruit SAMD boards

To be able to compile, run and automatically detect and display BOARD_NAME on Adafruit SAMD (Itsy-Bitsy M4, etc) boards, you have to copy the whole Adafruit SAMD Packages_Patches directory into Adafruit samd directory (~/.arduino15/packages/adafruit/hardware/samd/1.7.11).

Supposing the Adafruit SAMD core version is 1.7.11. These files must be copied into the directory:

• ~/.arduino15/packages/adafruit/hardware/samd/1.7.11/platform.txt
• ~/.arduino15/packages/adafruit/hardware/samd/1.7.11/cores/arduino/Print.h
• ~/.arduino15/packages/adafruit/hardware/samd/1.7.11/cores/arduino/Print.cpp

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz These files must be copied into the directory:

• ~/.arduino15/packages/adafruit/hardware/samd/x.yy.zz/platform.txt
• ~/.arduino15/packages/adafruit/hardware/samd/x.yy.zz/cores/arduino/Print.h
• ~/.arduino15/packages/adafruit/hardware/samd/x.yy.zz/cores/arduino/Print.cpp

6. For Seeeduino SAMD boards

To be able to compile, run and automatically detect and display BOARD_NAME on Seeeduino SAMD (XIAO M0, Wio Terminal, etc) boards, you have to copy the whole Seeeduino SAMD Packages_Patches directory into Seeeduino samd directory (~/.arduino15/packages/Seeeduino/hardware/samd/1.8.3).

Supposing the Seeeduino SAMD core version is 1.8.3. These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/samd/1.8.3/platform.txt
• ~/.arduino15/packages/Seeeduino/hardware/samd/1.8.3/cores/arduino/Arduino.h
• ~/.arduino15/packages/Seeeduino/hardware/samd/1.8.3/cores/arduino/Print.h
• ~/.arduino15/packages/Seeeduino/hardware/samd/1.8.3/cores/arduino/Print.cpp

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/platform.txt
• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/cores/arduino/Arduino.h
• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/cores/arduino/Print.h
• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/cores/arduino/Print.cpp

7. For STM32 boards

7.1 For STM32 boards to use LAN8720

To use LAN8720 on some STM32 boards

• Nucleo-144 (F429ZI, NUCLEO_F746NG, NUCLEO_F746ZG, NUCLEO_F756ZG)
• Discovery (DISCO_F746NG)
• STM32F4 boards (BLACK_F407VE, BLACK_F407VG, BLACK_F407ZE, BLACK_F407ZG, BLACK_F407VE_Mini, DIYMORE_F407VGT, FK407M1)

you have to copy the files stm32f4xx_hal_conf_default.h and stm32f7xx_hal_conf_default.h into STM32 stm32 directory (~/.arduino15/packages/STM32/hardware/stm32/2.3.0/system) to overwrite the old files.

Supposing the STM32 stm32 core version is 2.3.0. These files must be copied into the directory:

• ~/.arduino15/packages/STM32/hardware/stm32/2.3.0/system/STM32F4xx/stm32f4xx_hal_conf_default.h for STM32F4.
• ~/.arduino15/packages/STM32/hardware/stm32/2.3.0/system/STM32F7xx/stm32f7xx_hal_conf_default.h for Nucleo-144 STM32F7.

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz, these files must be copied into the corresponding directory:

• ~/.arduino15/packages/STM32/hardware/stm32/x.yy.zz/system/STM32F4xx/stm32f4xx_hal_conf_default.h
• `~/.arduino15/packages/STM32/hardware/stm32/x.yy.zz/system/STM32F7xx/stm32f7xx_hal_conf_default.h

7.2 For STM32 boards to use Serial1

To use Serial1 on some STM32 boards without Serial1 definition (Nucleo-144 NUCLEO_F767ZI, Nucleo-64 NUCLEO_L053R8, etc.) boards, you have to copy the files STM32 variant.h into STM32 stm32 directory (~/.arduino15/packages/STM32/hardware/stm32/2.3.0). You have to modify the files corresponding to your boards, this is just an illustration how to do.

Supposing the STM32 stm32 core version is 2.3.0. These files must be copied into the directory:

• ~/.arduino15/packages/STM32/hardware/stm32/2.3.0/variants/STM32F7xx/F765Z(G-I)T_F767Z(G-I)T_F777ZIT/NUCLEO_F767ZI/variant.h for Nucleo-144 NUCLEO_F767ZI.
• ~/.arduino15/packages/STM32/hardware/stm32/2.3.0/variants/STM32L0xx/L052R(6-8)T_L053R(6-8)T_L063R8T/NUCLEO_L053R8/variant.h for Nucleo-64 NUCLEO_L053R8.

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz, these files must be copied into the corresponding directory:

• ~/.arduino15/packages/STM32/hardware/stm32/x.yy.zz/variants/STM32F7xx/F765Z(G-I)T_F767Z(G-I)T_F777ZIT/NUCLEO_F767ZI/variant.h
• ~/.arduino15/packages/STM32/hardware/stm32/x.yy.zz/variants/STM32L0xx/L052R(6-8)T_L053R(6-8)T_L063R8T/NUCLEO_L053R8/variant.h

8. For RP2040-based boards using Earle Philhower arduino-pico core

8.1 To use BOARD_NAME

To be able to automatically detect and display BOARD_NAME on RP2040-based boards (RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040, GENERIC_RP2040, etc) boards, you have to copy the file RP2040 platform.txt into rp2040 directory (~/.arduino15/packages/rp2040/hardware/rp2040/1.4.0).

Supposing the rp2040 core version is 1.4.0. This file must be copied into the directory:

• ~/.arduino15/packages/rp2040/hardware/rp2040/1.4.0/platform.txt

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied into the directory:

• ~/.arduino15/packages/rp2040/hardware/rp2040/x.yy.zz/platform.txt

With core after v1.5.0, this step is not necessary anymore thanks to the PR Add -DBOARD_NAME="{build.board}" #136.

8.2 To avoid compile error relating to microsecondsToClockCycles

Some libraries, such as Adafruit DHT-sensor-library, require the definition of microsecondsToClockCycles(). To be able to compile and run on RP2040-based boards, you have to copy the files in RP2040 Arduino.h into rp2040 directory (~/.arduino15/packages/rp2040/hardware/rp2040/1.4.0).

Supposing the rp2040 core version is 1.4.0. This file must be copied to replace:

• ~/.arduino15/packages/rp2040/hardware/rp2040/1.4.0/cores/rp2040/Arduino.h

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied to replace:

• ~/.arduino15/packages/rp2040/hardware/rp2040/x.yy.zz/cores/rp2040/Arduino.h

With core after v1.5.0, this step is not necessary anymore thanks to the PR Add defs for compatibility #142.

9. For Portenta_H7 boards using Arduino IDE in Linux

To be able to upload firmware to Portenta_H7 using Arduino IDE in Linux (Ubuntu, etc.), you have to copy the file portenta_post_install.sh into mbed_portenta directory (~/.arduino15/packages/arduino/hardware/mbed_portenta/3.4.1/portenta_post_install.sh).

Then run the following command using sudo

$ cd ~/.arduino15/packages/arduino/hardware/mbed_portenta/3.4.1
$ chmod 755 portenta_post_install.sh
$ sudo ./portenta_post_install.sh

This will create the file /etc/udev/rules.d/49-portenta_h7.rules as follows:

# Portenta H7 bootloader mode UDEV rules

SUBSYSTEMS=="usb", ATTRS{idVendor}=="2341", ATTRS{idProduct}=="035b", GROUP="plugdev", MODE="0666"

Supposing the ArduinoCore-mbed core version is 3.4.1. Now only one file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/mbed_portenta/3.4.1/portenta_post_install.sh

Whenever a new version is installed, remember to copy this files into the new version directory. For example, new version is x.yy.zz

This file must be copied into the directory:

• ~/.arduino15/packages/arduino/hardware/mbed_portenta/x.yy.zz/portenta_post_install.sh

10. For RTL8720DN boards using AmebaD core

To avoid compile error relating to PROGMEM, you have to copy the file Realtek AmebaD core pgmspace.h into Realtek AmebaD directory (~/.arduino15/packages/realtek/hardware/AmebaD/3.1.4/cores/ambd/avr/pgmspace.h).

Supposing the Realtek AmebaD core version is 3.1.4. This file must be copied into the directory:

• ~/.arduino15/packages/realtek/hardware/AmebaD/3.1.4/cores/ambd/avr/pgmspace.h

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied into the directory:

• ~/.arduino15/packages/realtek/hardware/AmebaD/x.yy.zz/cores/ambd/avr/pgmspace.h

11. For SAMD21 and SAMD51 boards using ArduinoCore-fab-sam core

To avoid compile error relating to SAMD21/SAMD51, you have to copy the file ArduinoCore-fab-sam core pgmspace.h into ArduinoCore-fab-sam samd directory (~/.arduino15/packages/Fab_SAM_Arduino/hardware/samd/1.9.0/boards.txt).

Supposing the ArduinoCore-fab-sam samd core version is 1.9.0. This file must be copied into the directory:

• ~/.arduino15/packages/Fab_SAM_Arduino/hardware/samd/1.9.0/boards.txt

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz This file must be copied into the directory:

• ~/.arduino15/packages/Fab_SAM_Arduino/hardware/samd/x.yy.zz/boards.txt

12. For Seeeduino RP2040 boards

To be able to compile, run and automatically detect and display BOARD_NAME on Seeeduino RP2040 (XIAO RP2040, Wio RP2040 Mini) boards, you have to copy the whole Seeeduino RP2040 Packages_Patches directory into Seeeduino samd directory (~/.arduino15/packages/Seeeduino/hardware/rp2040/2.7.2).

Supposing the Seeeduino RP2040 core version is 2.7.2. These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/rp2040/2.7.2/boards.txt
• ~/.arduino15/packages/Seeeduino/hardware/rp2040/2.7.2/variants/Seeed_XIAO_RP2040/pins_arduino.h

Whenever a new version is installed, remember to copy this file into the new version directory. For example, new version is x.yy.zz These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/boards.txt
• ~/.arduino15/packages/Seeeduino/hardware/samd/x.yy.zz/variants/Seeed_XIAO_RP2040/pins_arduino.h

---

13. For Seeeduino nRF52840 boards

To be able to compile and run on Xiao nRF52840 boards, you have to copy the whole nRF52 1.0.0 directory into Seeeduino nRF52 directory (~/.arduino15/packages/Seeeduino/hardware/nrf52/1.0.0).

Supposing the Seeeduino nRF52 version is 1.0.0. These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/nrf52/1.0.0/platform.txt
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/1.0.0/cores/nRF5/Print.h
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/1.0.0/cores/nRF5/Print.cpp
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/1.0.0/cores/nRF5/Udp.h

Whenever a new version is installed, remember to copy these files into the new version directory. For example, new version is x.yy.z These files must be copied into the directory:

• ~/.arduino15/packages/Seeeduino/hardware/nrf52/x.yy.z/platform.txt
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/x.yy.z/cores/nRF5/Print.h
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/x.yy.z/cores/nRF5/Print.cpp
• ~/.arduino15/packages/Seeeduino/hardware/nrf52/x.yy.z/cores/nRF5/Udp.h

---

---

Usage

Class Constructor

ESP8266_AT_WebServer server(80);

Creates the ESP8266_AT_WebServer class object.

Parameters:

host port number: int port (default is the standard HTTP port 80)

Basic Operations

Starting the server

void begin();

Handling incoming client requests

void handleClient();

Disabling the server

void close();
void stop();

Both methods function the same

Client request handlers

void on();
void addHandler();
void onNotFound();
void onFileUpload();	

Example:

server.on("/", handlerFunction);
server.onNotFound(handlerFunction);   // called when handler is not assigned
server.onFileUpload(handlerFunction); // handle file uploads

Sending responses to the client

void send();
void send_P();

Parameters:

code - HTTP response code, can be 200 or 404, etc.

content_type - HTTP content type, like "text/plain" or "image/png", etc.

content - actual content body

Advanced Options

Getting information about request arguments

const String & arg();
const String & argName();
int args();
bool hasArg();

Function usage:

arg - get request argument value, use arg("plain") to get POST body

argName - get request argument name

args - get arguments count

hasArg - check if argument exist

Getting information about request headers

const String & header();
const String & headerName();
const String & hostHeader();
int headers();
bool hasHeader();

Function usage:

header - get request header value

headerName - get request header name

hostHeader - get request host header if available, else empty string

headers - get header count

hasHeader - check if header exist

Authentication

bool authenticate();
void requestAuthentication();

Function usage:

authenticate - server authentication, returns true if client is authenticated else false

requestAuthentication - sends authentication failure response to the client

Example Usage:

if(!server.authenticate(username, password))
{
  server.requestAuthentication();
}

Other Function Calls

const String & uri(); // get the current uri
HTTPMethod  method(); // get the current method 
WiFiClient client(); // get the current client
HTTPUpload & upload(); // get the current upload
void setContentLength(); // set content length
void sendHeader(); // send HTTP header
void sendContent(); // send content
void sendContent_P(); 
void collectHeaders(); // set the request headers to collect
void serveStatic();
size_t streamFile();

---

---

Examples

Also see examples:

1. AdvancedWebServer
2. AdvancedWebServer_STM32
3. ConnectWPA
4. HelloServer
5. HelloServer2
6. HttpBasicAuth
7. MQTTClient_Auth
8. MQTTClient_Basic
9. MQTT_ThingStream
10. PostServer
11. ScanNetworks
12. SimpleAuthentication
13. UdpNTPClient
14. UdpSendReceive
15. WebClient
16. WebClientRepeating
17. WebServer
18. WebServerAP
19. ATWebServer_BigData New

---

---

Example AdvancedWebServer

Please take a look at other examples, as well.

1. File AdvancedWebServer.ino

ESP8266_AT_WebServer/examples/AdvancedWebServer/AdvancedWebServer.ino

Lines 60 to 305 in 1839e2f

	#include "defines.h"
	int status = WL_IDLE_STATUS; // the Wifi radio's status
	int reqCount = 0; // number of requests received
	#define WEBSERVER_PORT 80
	ESP8266_AT_WebServer server(WEBSERVER_PORT);
	//WiFiServer server(WEBSERVER_PORT);
	const int led = 13;
	void handleRoot()
	{
	#define BUFFER_SIZE 512
	digitalWrite(led, 1);
	char temp[BUFFER_SIZE];
	int sec = millis() / 1000;
	int min = sec / 60;
	int hr = min / 60;
	int day = hr / 24;
	hr = hr % 24;
	snprintf(temp, BUFFER_SIZE - 1,
	"<html>\
	<head>\
	<meta http-equiv='refresh' content='5'/>\
	<title>%s</title>\
	<style>\
	body { background-color: #cccccc; font-family: Arial, Helvetica, Sans-Serif; Color: #000088; }\
	</style>\
	</head>\
	<body>\
	<h1>Hello from %s</h1>\
	<h3>running AdvancedWebServer</h3>\
	<h3>on %s</h3>\
	<p>Uptime: %d d %02d:%02d:%02d</p>\
	<img src=\"/test.svg\" />\
	</body>\
	</html>", BOARD_NAME, BOARD_NAME, SHIELD_TYPE, day, hr, min % 60, sec % 60);
	server.send(200, F("text/html"), temp);
	digitalWrite(led, 0);
	}
	void handleNotFound()
	{
	digitalWrite(led, 1);
	String message = F("File Not Found\n\n");
	message += F("URI: ");
	message += server.uri();
	message += F("\nMethod: ");
	message += (server.method() == HTTP_GET) ? F("GET") : F("POST");
	message += F("\nArguments: ");
	message += server.args();
	message += F("\n");
	for (uint8_t i = 0; i < server.args(); i++)
	{
	message += " " + server.argName(i) + ": " + server.arg(i) + "\n";
	}
	server.send(404, F("text/plain"), message);
	digitalWrite(led, 0);
	}
	// You can also redefine here (1, 2, 4, 6) to override
	#if !defined(MULTIPLY_FACTOR)
	#define MULTIPLY_FACTOR 1
	#elif (MULTIPLY_FACTOR > 6)
	#undef MULTIPLY_FACTOR
	#define MULTIPLY_FACTOR 6
	#endif
	String out;
	#define ORIGINAL_STR_LEN (2048 * MULTIPLY_FACTOR)
	void drawGraph()
	{
	//static String out;
	static uint16_t previousStrLen = ORIGINAL_STR_LEN;
	//if (out.length() == 0)
	{
	//AT_LOGWARN1(F("String Len = 0, extend to"), ORIGINAL_STR_LEN);
	//out.reserve(ORIGINAL_STR_LEN);
	}
	#if (MULTIPLY_FACTOR == 2)
	out = F( "<svg xmlns=\"http://www.w3.org/2000/svg\" version=\"1.1\" width=\"610\" height=\"150\">\n" \
	"<rect width=\"610\" height=\"150\" fill=\"rgb(250, 230, 210)\" stroke-width=\"3\" stroke=\"rgb(0, 0, 0)\" />\n" \
	"<g stroke=\"blue\">\n");
	#elif (MULTIPLY_FACTOR == 4)
	out = F( "<svg xmlns=\"http://www.w3.org/2000/svg\" version=\"1.1\" width=\"1210\" height=\"150\">\n" \
	"<rect width=\"1210\" height=\"150\" fill=\"rgb(250, 230, 210)\" stroke-width=\"3\" stroke=\"rgb(0, 0, 0)\" />\n" \
	"<g stroke=\"blue\">\n");
	#elif (MULTIPLY_FACTOR == 6)
	out = F( "<svg xmlns=\"http://www.w3.org/2000/svg\" version=\"1.1\" width=\"1810\" height=\"150\">\n" \
	"<rect width=\"1810\" height=\"150\" fill=\"rgb(250, 230, 210)\" stroke-width=\"3\" stroke=\"rgb(0, 0, 0)\" />\n" \
	"<g stroke=\"blue\">\n");
	#else // (MULTIPLY_FACTOR == 1)
	out = F( "<svg xmlns=\"http://www.w3.org/2000/svg\" version=\"1.1\" width=\"310\" height=\"150\">\n" \
	"<rect width=\"310\" height=\"150\" fill=\"rgb(250, 230, 210)\" stroke-width=\"3\" stroke=\"rgb(0, 0, 0)\" />\n" \
	"<g stroke=\"blue\">\n");
	#endif
	char temp[70];
	int y = rand() % 130;
	//for (int x = 10; x < 300; x += 10)
	for (int x = 10; x < (300 * MULTIPLY_FACTOR); x += 10)
	{
	int y2 = rand() % 130;
	sprintf(temp, "<line x1=\"%d\" y1=\"%d\" x2=\"%d\" y2=\"%d\" stroke-width=\"2\" />\n", x, 140 - y, x + 10, 140 - y2);
	out += temp;
	y = y2;
	}
	out += F("</g>\n</svg>\n");
	AT_LOGINFO1(F("String Len = "), out.length());
	if (out.length() > previousStrLen)
	{
	AT_LOGERROR3(F("String Len > "), previousStrLen, F(", extend to"), out.length() + 48);
	previousStrLen = out.length() + 48;
	out.reserve(previousStrLen);
	}
	else
	{
	server.send(200, "image/svg+xml", out);
	}
	}
	void setup()
	{
	out.reserve(ORIGINAL_STR_LEN);
	pinMode(led, OUTPUT);
	digitalWrite(led, 0);
	Serial.begin(115200);
	while (!Serial && millis() < 5000);
	Serial.print(F("\nStarting AdvancedWebServer on "));
	Serial.print(BOARD_NAME);
	Serial.print(F(" with "));
	Serial.println(SHIELD_TYPE);
	Serial.println(ESP8266_AT_WEBSERVER_VERSION);
	// initialize serial for ESP module
	EspSerial.begin(115200);
	// initialize ESP module
	WiFi.init(&EspSerial);
	Serial.println(F("WiFi shield init done"));
	// check for the presence of the shield
	if (WiFi.status() == WL_NO_SHIELD)
	{
	Serial.println(F("WiFi shield not present"));
	// don't continue
	while (true);
	}
	// attempt to connect to WiFi network
	while ( status != WL_CONNECTED)
	{
	Serial.print(F("Connecting to WPA SSID: "));
	Serial.println(ssid);
	// Connect to WPA/WPA2 network
	status = WiFi.begin(ssid, pass);
	}
	server.on(F("/"), handleRoot);
	server.on(F("/test.svg"), drawGraph);
	server.on(F("/inline"), []()
	{
	server.send(200, F("text/plain"), F("This works as well"));
	});
	server.onNotFound(handleNotFound);
	server.begin();
	Serial.print(F("HTTP server started @ "));
	Serial.print(WiFi.localIP());
	Serial.print(F(", Port = "));
	Serial.println(WEBSERVER_PORT);
	}
	void heartBeatPrint()
	{
	static int num = 1;
	Serial.print(F("."));
	if (num == 80)
	{
	Serial.println();
	num = 1;
	}
	else if (num++ % 10 == 0)
	{
	Serial.print(F(" "));
	}
	}
	void check_status()
	{
	static unsigned long checkstatus_timeout = 0;
	#define STATUS_CHECK_INTERVAL 10000L
	// Send status report every STATUS_REPORT_INTERVAL (60) seconds: we don't need to send updates frequently if there is no status change.
	if ((millis() > checkstatus_timeout) || (checkstatus_timeout == 0))
	{
	heartBeatPrint();
	checkstatus_timeout = millis() + STATUS_CHECK_INTERVAL;
	}
	}
	void loop()
	{
	server.handleClient();
	check_status();
	}

---

2. File defines.h

ESP8266_AT_WebServer/examples/AdvancedWebServer/defines.h

Lines 15 to 433 in 1839e2f

	#ifndef defines_h
	#define defines_h
	//#define HTTP_UPLOAD_BUFLEN 4096
	#define DEBUG_ESP8266_AT_WEBSERVER_PORT Serial
	// Debug Level from 0 to 4
	#define _ESP_AT_LOGLEVEL_ 1
	#define USING_WIZFI360 true
	#if (USING_WIZFI360) || defined(ARDUINO_WIZNET_WIZFI360_EVB_PICO)
	#define USE_ESP32_AT true
	#else
	// Uncomment to use ESP32-AT commands
	//#define USE_ESP32_AT true
	#endif
	#if USE_ESP32_AT
	#warning Using ESP32-AT WiFi and ESP8266_AT_WebServer Library
	#define SHIELD_TYPE "ESP32-AT & ESP8266_AT_WebServer Library"
	#else
	#warning Using ESP8266-AT WiFi with ESP8266_AT_WebServer Library
	#define SHIELD_TYPE "ESP8266-AT & ESP8266_AT_WebServer Library"
	#endif
	#if ( defined(ARDUINO_SAMD_ZERO) || defined(ARDUINO_SAMD_MKR1000) || defined(ARDUINO_SAMD_MKRWIFI1010) \
	|| defined(ARDUINO_SAMD_NANO_33_IOT) || defined(ARDUINO_SAMD_MKRFox1200) || defined(ARDUINO_SAMD_MKRWAN1300) || defined(ARDUINO_SAMD_MKRWAN1310) \
	|| defined(ARDUINO_SAMD_MKRGSM1400) || defined(ARDUINO_SAMD_MKRNB1500) || defined(ARDUINO_SAMD_MKRVIDOR4000) || defined(__SAMD21G18A__) \
	|| defined(ARDUINO_SAMD_CIRCUITPLAYGROUND_EXPRESS) || defined(__SAMD21E18A__) || defined(__SAMD51__) || defined(__SAMD51J20A__) || defined(__SAMD51J19A__) \
	|| defined(__SAMD51G19A__) || defined(__SAMD51P19A__) || defined(__SAMD21G18A__) )
	#define MULTIPLY_FACTOR 2
	#if defined(ESP8266_AT_USE_SAMD)
	#undef ESP8266_AT_USE_SAMD
	#endif
	#define ESP8266_AT_USE_SAMD true
	#endif
	#if (defined(NRF52840_FEATHER) || defined(NRF52832_FEATHER) || defined(NRF52_SERIES) || defined(ARDUINO_NRF52_ADAFRUIT) || \
	defined(NRF52840_FEATHER_SENSE) || defined(NRF52840_ITSYBITSY) || defined(NRF52840_CIRCUITPLAY) || \
	defined(NRF52840_CLUE) || defined(NRF52840_METRO) || defined(NRF52840_PCA10056) || defined(PARTICLE_XENON) || \
	defined(NRF52840_LED_GLASSES) || defined(MDBT50Q_RX) || defined(NINA_B302_ublox) || defined(NINA_B112_ublox) || \
	defined(ARDUINO_Seeed_XIAO_nRF52840) || defined(ARDUINO_Seeed_XIAO_nRF52840_Sense) || \
	defined(ARDUINO_SEEED_XIAO_NRF52840) || defined(ARDUINO_SEEED_XIAO_NRF52840_SENSE) )
	#define MULTIPLY_FACTOR 4
	#if defined(ESP8266_AT_USE_NRF528XX)
	#undef ESP8266_AT_USE_NRF528XX
	#endif
	#define ESP8266_AT_USE_NRF528XX true
	#endif
	#if ( defined(ARDUINO_SAM_DUE) || defined(__SAM3X8E__) )
	#if defined(ESP8266_AT_USE_SAM_DUE)
	#undef ESP8266_AT_USE_SAM_DUE
	#endif
	#define ESP8266_AT_USE_SAM_DUE true
	#endif
	#if ( defined(STM32F0) || defined(STM32F1) || defined(STM32F2) || defined(STM32F3) ||defined(STM32F4) || defined(STM32F7) || \
	defined(STM32L0) || defined(STM32L1) || defined(STM32L4) || defined(STM32H7) ||defined(STM32G0) || defined(STM32G4) || \
	defined(STM32WB) || defined(STM32MP1) )
	#if defined(ESP8266_AT_USE_STM32)
	#undef ESP8266_AT_USE_STM32
	#endif
	#define ESP8266_AT_USE_STM32 true
	#endif
	#if ( defined(ARDUINO_AVR_ADK) || defined(ARDUINO_AVR_MEGA) || defined(ARDUINO_AVR_MEGA2560) )
	#if defined(ESP_AT_USE_AVR)
	#undef ESP_AT_USE_AVR
	#endif
	#define ESP_AT_USE_AVR true
	#endif
	#ifdef CORE_TEENSY
	// For Teensy 4.1/4.0
	//#define EspSerial Serial1 //Serial1, Pin RX1 : 0, TX1 : 1
	#define EspSerial Serial2 //Serial2, Pin RX2 : 7, TX2 : 8
	//#define EspSerial Serial3 //Serial3, Pin RX3 : 15, TX3 : 14
	//#define EspSerial Serial4 //Serial4, Pin RX4 : 16, TX4 : 17
	#if defined(__IMXRT1062__)
	// For Teensy 4.1/4.0
	#define MULTIPLY_FACTOR 6
	#if defined(ARDUINO_TEENSY41)
	#define BOARD_TYPE "TEENSY 4.1"
	// Use true for NativeEthernet Library, false if using other Ethernet libraries
	#define USE_NATIVE_ETHERNET true
	#elif defined(ARDUINO_TEENSY40)
	#define BOARD_TYPE "TEENSY 4.0"
	#else
	#define BOARD_TYPE "TEENSY 4.x"
	#endif
	#elif defined(__MK66FX1M0__)
	#define BOARD_TYPE "Teensy 3.6"
	#elif defined(__MK64FX512__)
	#define BOARD_TYPE "Teensy 3.5"
	#elif defined(__MKL26Z64__)
	#define BOARD_TYPE "Teensy LC"
	#elif defined(__MK20DX256__)
	#define BOARD_TYPE "Teensy 3.2" // and Teensy 3.1 (obsolete)
	#elif defined(__MK20DX128__)
	#define BOARD_TYPE "Teensy 3.0"
	#elif defined(__AVR_AT90USB1286__)
	#error Teensy 2.0++ not supported yet
	#elif defined(__AVR_ATmega32U4__)
	#error Teensy 2.0 not supported yet
	#else
	// For Other Boards
	#define BOARD_TYPE "Unknown Teensy Board"
	#endif
	#elif defined(ESP8266_AT_USE_SAMD)
	// For SAMD
	#define EspSerial Serial1
	#if defined(ARDUINO_SAMD_ZERO)
	#define BOARD_TYPE "SAMD Zero"
	#elif defined(ARDUINO_SAMD_MKR1000)
	#define BOARD_TYPE "SAMD MKR1000"
	#elif defined(ARDUINO_SAMD_MKRWIFI1010)
	#define BOARD_TYPE "SAMD MKRWIFI1010"
	#elif defined(ARDUINO_SAMD_NANO_33_IOT)
	#define BOARD_TYPE "SAMD NANO_33_IOT"
	#elif defined(ARDUINO_SAMD_MKRFox1200)
	#define BOARD_TYPE "SAMD MKRFox1200"
	#elif ( defined(ARDUINO_SAMD_MKRWAN1300) || defined(ARDUINO_SAMD_MKRWAN1310) )
	#define BOARD_TYPE "SAMD MKRWAN13X0"
	#elif defined(ARDUINO_SAMD_MKRGSM1400)
	#define BOARD_TYPE "SAMD MKRGSM1400"
	#elif defined(ARDUINO_SAMD_MKRNB1500)
	#define BOARD_TYPE "SAMD MKRNB1500"
	#elif defined(ARDUINO_SAMD_MKRVIDOR4000)
	#define BOARD_TYPE "SAMD MKRVIDOR4000"
	#elif defined(ARDUINO_SAMD_CIRCUITPLAYGROUND_EXPRESS)
	#define BOARD_TYPE "SAMD ARDUINO_SAMD_CIRCUITPLAYGROUND_EXPRESS"
	#elif defined(ADAFRUIT_FEATHER_M0_EXPRESS)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_FEATHER_M0_EXPRESS"
	#elif defined(ADAFRUIT_METRO_M0_EXPRESS)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_METRO_M0_EXPRESS"
	#elif defined(ADAFRUIT_CIRCUITPLAYGROUND_M0)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_CIRCUITPLAYGROUND_M0"
	#elif defined(ADAFRUIT_GEMMA_M0)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_GEMMA_M0"
	#elif defined(ADAFRUIT_TRINKET_M0)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_TRINKET_M0"
	#elif defined(ADAFRUIT_ITSYBITSY_M0)
	#define BOARD_TYPE "SAMD21 ADAFRUIT_ITSYBITSY_M0"
	#elif defined(ARDUINO_SAMD_HALLOWING_M0)
	#define BOARD_TYPE "SAMD21 ARDUINO_SAMD_HALLOWING_M0"
	#elif defined(ADAFRUIT_METRO_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_METRO_M4_EXPRESS"
	#elif defined(ADAFRUIT_GRAND_CENTRAL_M4)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_GRAND_CENTRAL_M4"
	#elif defined(ADAFRUIT_FEATHER_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_FEATHER_M4_EXPRESS"
	#elif defined(ADAFRUIT_ITSYBITSY_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_ITSYBITSY_M4_EXPRESS"
	#elif defined(ADAFRUIT_TRELLIS_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_TRELLIS_M4_EXPRESS"
	#elif defined(ADAFRUIT_PYPORTAL)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYPORTAL"
	#elif defined(ADAFRUIT_PYPORTAL_M4_TITANO)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYPORTAL_M4_TITANO"
	#elif defined(ADAFRUIT_PYBADGE_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYBADGE_M4_EXPRESS"
	#elif defined(ADAFRUIT_METRO_M4_AIRLIFT_LITE)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_METRO_M4_AIRLIFT_LITE"
	#elif defined(ADAFRUIT_PYGAMER_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYGAMER_M4_EXPRESS"
	#elif defined(ADAFRUIT_PYGAMER_ADVANCE_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYGAMER_ADVANCE_M4_EXPRESS"
	#elif defined(ADAFRUIT_PYBADGE_AIRLIFT_M4)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_PYBADGE_AIRLIFT_M4"
	#elif defined(ADAFRUIT_MONSTER_M4SK_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_MONSTER_M4SK_EXPRESS"
	#elif defined(ADAFRUIT_HALLOWING_M4_EXPRESS)
	#define BOARD_TYPE "SAMD51 ADAFRUIT_HALLOWING_M4_EXPRESS"
	#elif defined(SEEED_WIO_TERMINAL)
	#define BOARD_TYPE "SAMD SEEED_WIO_TERMINAL"
	#elif defined(SEEED_FEMTO_M0)
	#define BOARD_TYPE "SAMD SEEED_FEMTO_M0"
	#elif defined(SEEED_XIAO_M0)
	#define BOARD_TYPE "SAMD SEEED_XIAO_M0"
	#elif defined(Wio_Lite_MG126)
	#define BOARD_TYPE "SAMD SEEED Wio_Lite_MG126"
	#elif defined(WIO_GPS_BOARD)
	#define BOARD_TYPE "SAMD SEEED WIO_GPS_BOARD"
	#elif defined(SEEEDUINO_ZERO)
	#define BOARD_TYPE "SAMD SEEEDUINO_ZERO"
	#elif defined(SEEEDUINO_LORAWAN)
	#define BOARD_TYPE "SAMD SEEEDUINO_LORAWAN"
	#elif defined(SEEED_GROVE_UI_WIRELESS)
	#define BOARD_TYPE "SAMD SEEED_GROVE_UI_WIRELESS"
	#elif defined(__SAMD21E18A__)
	#define BOARD_TYPE "SAMD21E18A"
	#elif defined(__SAMD21G18A__)
	#define BOARD_TYPE "SAMD21G18A"
	#elif defined(__SAMD51G19A__)
	#define BOARD_TYPE "SAMD51G19A"
	#elif defined(__SAMD51J19A__)
	#define BOARD_TYPE "SAMD51J19A"
	#elif defined(__SAMD51J20A__)
	#define BOARD_TYPE "SAMD51J20A"
	#elif defined(__SAM3X8E__)
	#define BOARD_TYPE "SAM3X8E"
	#elif defined(__CPU_ARC__)
	#define BOARD_TYPE "CPU_ARC"
	#elif defined(__SAMD51__)
	#define BOARD_TYPE "SAMD51"
	#else
	#define BOARD_TYPE "SAMD Unknown"
	#endif
	#elif (ESP8266_AT_USE_NRF528XX)
	#if defined(NRF52840_FEATHER)
	#define BOARD_TYPE "NRF52840_FEATHER_EXPRESS"
	#elif defined(NRF52832_FEATHER)
	#define BOARD_TYPE "NRF52832_FEATHER"
	#elif defined(NRF52840_FEATHER_SENSE)
	#define BOARD_TYPE "NRF52840_FEATHER_SENSE"
	#elif defined(NRF52840_ITSYBITSY)
	#define BOARD_TYPE "NRF52840_ITSYBITSY_EXPRESS"
	#elif defined(NRF52840_CIRCUITPLAY)
	#define BOARD_TYPE "NRF52840_CIRCUIT_PLAYGROUND"
	#elif defined(NRF52840_CLUE)
	#define BOARD_TYPE "NRF52840_CLUE"
	#elif defined(NRF52840_METRO)
	#define BOARD_TYPE "NRF52840_METRO_EXPRESS"
	#elif defined(NRF52840_PCA10056)
	#define BOARD_TYPE "NORDIC_NRF52840DK"
	#elif defined(NINA_B302_ublox)
	#define BOARD_TYPE "NINA_B302_ublox"
	#elif defined(NINA_B112_ublox)
	#define BOARD_TYPE "NINA_B112_ublox"
	#elif defined(PARTICLE_XENON)
	#define BOARD_TYPE "PARTICLE_XENON"
	#elif defined(MDBT50Q_RX)
	#define BOARD_TYPE "RAYTAC_MDBT50Q_RX"
	#elif defined(ARDUINO_NRF52_ADAFRUIT)
	#define BOARD_TYPE "ARDUINO_NRF52_ADAFRUIT"
	#else
	#define BOARD_TYPE "nRF52 Unknown"
	#endif
	#define EspSerial Serial1
	#elif defined(ESP8266_AT_USE_SAM_DUE)
	// For SAM DUE
	#define EspSerial Serial1
	#define BOARD_TYPE "SAM DUE"
	#elif defined(ESP8266_AT_USE_STM32)
	// For STM32
	#warning EspSerial using SERIAL_PORT_HARDWARE, can be Serial or Serial1. See your board variant.h
	#define EspSerial SERIAL_PORT_HARDWARE //Serial1
	#if defined(STM32F0)
	#warning STM32F0 board selected
	#define BOARD_TYPE "STM32F0"
	#elif defined(STM32F1)
	#warning STM32F1 board selected
	#define BOARD_TYPE "STM32F1"
	#elif defined(STM32F2)
	#warning STM32F2 board selected
	#define BOARD_TYPE "STM32F2"
	#elif defined(STM32F3)
	#warning STM32F3 board selected
	#define BOARD_TYPE "STM32F3"
	#elif defined(STM32F4)
	#warning STM32F4 board selected
	#define BOARD_TYPE "STM32F4"
	#elif defined(STM32F7)
	#if defined(ARDUINO_NUCLEO_F767ZI)
	#warning Nucleo-144 NUCLEO_F767ZI board selected, using HardwareSerial Serial1 @ pin D0/RX and D1/TX
	// RX TX
	HardwareSerial Serial1(D0, D1);
	#else
	#warning STM32F7 board selected
	#define BOARD_TYPE "STM32F7"
	#endif
	#elif defined(STM32L0)
	#if defined(ARDUINO_NUCLEO_L053R8)
	#warning Nucleo-64 NUCLEO_L053R8 board selected, using HardwareSerial Serial1 @ pin D0/RX and D1/TX
	// RX TX
	HardwareSerial Serial1(D0, D1); // (PA3, PA2);
	#else
	#warning STM32L0 board selected
	#define BOARD_TYPE "STM32L0"
	#endif
	#elif defined(STM32L1)
	#warning STM32L1 board selected
	#define BOARD_TYPE "STM32L1"
	#elif defined(STM32L4)
	#warning STM32L4 board selected
	#define BOARD_TYPE "STM32L4"
	#elif defined(STM32H7)
	#warning STM32H7 board selected
	#define BOARD_TYPE "STM32H7"
	#elif defined(STM32G0)
	#warning STM32G0 board selected
	#define BOARD_TYPE "STM32G0"
	#elif defined(STM32G4)
	#warning STM32G4 board selected
	#define BOARD_TYPE "STM32G4"
	#elif defined(STM32WB)
	#warning STM32WB board selected
	#define BOARD_TYPE "STM32WB"
	#elif defined(STM32MP1)
	#warning STM32MP1 board selected
	#define BOARD_TYPE "STM32MP1"
	#else
	#warning STM32 unknown board selected
	#define BOARD_TYPE "STM32 Unknown"
	#endif
	#elif defined(BOARD_SIPEED_MAIX_DUINO)
	#warning SIPEED_MAIX_DUINO board selected
	#define BOARD_TYPE "BOARD_SIPEED_MAIX_DUINO"
	#define EspSerial Serial1
	#elif ( defined(ARDUINO_NANO_RP2040_CONNECT) || defined(ARDUINO_ARCH_RP2040) || defined(ARDUINO_RASPBERRY_PI_PICO) || \
	defined(ARDUINO_GENERIC_RP2040) || defined(ARDUINO_ADAFRUIT_FEATHER_RP2040) )
	#warning RASPBERRY_PI_PICO board selected
	#define MULTIPLY_FACTOR 6
	#if defined(ARDUINO_ARCH_MBED)
	#warning Using ARDUINO_ARCH_MBED
	#if ( defined(ARDUINO_NANO_RP2040_CONNECT) || defined(ARDUINO_RASPBERRY_PI_PICO) || \
	defined(ARDUINO_GENERIC_RP2040) || defined(ARDUINO_ADAFRUIT_FEATHER_RP2040) )
	// Only undef known BOARD_NAME to use better one
	#undef BOARD_NAME
	#endif
	#if defined(ARDUINO_RASPBERRY_PI_PICO)
	#define BOARD_NAME "MBED RASPBERRY_PI_PICO"
	#elif defined(ARDUINO_ADAFRUIT_FEATHER_RP2040)
	#define BOARD_NAME "MBED ADAFRUIT_FEATHER_RP2040"
	#elif defined(ARDUINO_GENERIC_RP2040)
	#define BOARD_NAME "MBED GENERIC_RP2040"
	#elif defined(ARDUINO_NANO_RP2040_CONNECT)
	#define BOARD_NAME "MBED NANO_RP2040_CONNECT"
	#else
	// Use default BOARD_NAME if exists
	#if !defined(BOARD_NAME)
	#define BOARD_NAME "MBED Unknown RP2040"
	#endif
	#endif
	#endif
	#if defined(ARDUINO_WIZNET_WIZFI360_EVB_PICO)
	#warning WIZNET_WIZFI360_EVB_PICO
	#define EspSerial Serial2
	#else
	#define EspSerial Serial1
	#endif
	#elif (ESP_AT_USE_AVR)
	#if defined(ARDUINO_AVR_MEGA2560)
	#define BOARD_TYPE "AVR Mega2560"
	#elif defined(ARDUINO_AVR_MEGA)
	#define BOARD_TYPE "AVR Mega"
	#else
	#define BOARD_TYPE "AVR ADK"
	#endif
	// For Mega, use Serial1 or Serial3
	#define EspSerial Serial3
	#else
	#error Unknown or unsupported Board. Please check your Tools->Board setting.
	#endif
	#ifndef BOARD_NAME
	#define BOARD_NAME BOARD_TYPE
	#endif
	////////////////////////////////////////////
	#if !defined(MULTIPLY_FACTOR)
	#define MULTIPLY_FACTOR 1
	#elif (MULTIPLY_FACTOR > 6)
	#undef MULTIPLY_FACTOR
	#define MULTIPLY_FACTOR 6
	#endif
	////////////////////////////////////////////
	#include <ESP8266_AT_WebServer.h>
	char ssid[] = "YOUR_SSID"; // your network SSID (name)
	char pass[] = "12345678"; // your network password
	#endif //defines_h

---

Debug Terminal Output Samples

1. AdvancedWebServer on Adafruit NRF52840_ITSYBITSY_EXPRESS using ESP8266-AT shield

The following are debug terminal output when running example AdvancedWebServer on NRF52840_ITSYBITSY_EXPRESS and ESP8266-AT shield.

Starting AdvancedWebServer on NRF52840_ITSYBITSY_EXPRESS
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Initializing ESP module
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to WPA SSID: HueNet1
Starting server
[ESP_AT] Server started on port 80
HTTP server started @ 192.168.2.44
[ESP_AT] New client 0
ESP8266_AT_WebServer::handleClient: New Client
method:  GET
url:  /
search:
headerName: Host
headerValue: 192.168.2.44
headerName: Connection
headerValue: keep-alive
headerName: Cache-Control
headerValue: max-age=0
headerName: Upgrade-Insecure-Requests
headerValue: 1
headerName: DNT
headerValue: 1
headerName: Accept
headerValue: text/html,application/xhtml+xml,application/xml;q=0.9,image/webp,image/apng,*/*;q=0.8,application/signed-exchange;v=b3;q=0.9
headerName: Referer
headerValue: http://192.168.2.44/
headerName: Accept-Encoding
headerValue: gzip, deflate
[ESP_AT] TIMEOUT: 104
args:
args count:  0
args:
args count:  0
Request: /
Arguments: 
Final list of key/value pairs:
ESP8266_AT_WebServer::_handleRequest handle
[ESP_AT] ReqHandler::handle
AT_WebServer::send1: len =  314
content =  <html><head><meta http-equiv='refresh' content='5'/><title>ESP-AT NRF52840_ITSYBITSY_EXPRESS</title><style>body { background-color: #cccccc; font-family: Arial, Helvetica, Sans-Serif; Color: #000088; }</style></head><body><h1>Hello from ESP-AT</h1><h3>on NRF52840_ITSYBITSY_EXPRESS</h3><p>Uptime: 0 d 00:00:23</p><img src="/test.svg" /></body></html>
AT_WebServer::_prepareHeader sendHeader Conn close
AT_WebServer::send1: write header =  HTTP/1.1 200 OK
Content-Type: text/html
Content-Length: 314
Connection: close

ESP8266_AT_WebServer::sendContent: Client.write content:  <html><head><meta http-equiv='refresh' content='5'/><title>ESP-AT AVR Mega</title><style>body { background-color: #cccccc; font-family: Arial, Helvetica, Sans-Serif; Color: #000088; }</style></head><body><h1>Hello from ESP-AT</h1><h3>on NRF52840_ITSYBITSY_EXPRESS</h3><p>Uptime: 0 d 00:00:23</p><img src="/test.svg" /></body></html>
[ESP_AT] ReqHandler::handle done
ESP8266_AT_WebServer::_handleRequest OK
ESP8266_AT_WebServer::handleClient: Don't keepCurrentClient
ESP8266_AT_WebServer::handleClient: Client disconnected
[ESP_AT] New client 0
ESP8266_AT_WebServer::handleClient: New Client
method:  GET
url:  /test.svg
search:
headerName: Host
headerValue: 192.168.2.44
headerName: Connection
headerValue: keep-alive
headerName: User-Agent
headerValue: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/537.36 ike Gecko) Chrome/84.0.4147.89 Safari/537.36
headerName: DNT
headerValue: 1
headerName: Accept
headerValue: image/webp,image/apng,image/*,*/*;q=0.8
args:
args count:  0
args:
args count:  0
[ESP_AT] TIMEOUT: 81
Request: /test.svg
Arguments: 
Final list of key/value pairs:
ESP8266_AT_WebServer::_handleRequest handle
[ESP_AT] ReqHandler::handle
AT_WebServer::send1: len =  1949
content =  <svg xmlns="http://www.w3.org/2000/svg" version="1.1" width="310" height="150">
<rect width="310" height="150" fill="rgb(250, 230, 210)" stroke-width="1" stroke="rgb(0, 0, 0)" />
<g stroke="blue">
<line x1="10" y1="103" x2="20" y2="131" stroke-width="1" />
<line x1="20" y1="131" x2="30" y2="99" stroke-width="1" />
<line x1="30" y1="99" x2="40" y2="16" stroke-width="1" />
<line x1="40" y1="16" x2="50" y2="100" stroke-width="1" />
<line x1="50" y1="100" x2="60" y2="40" stroke-width="1" />
<line x1="60" y1="40" x2="70" y2="110" stroke-width="1" />
<line x1="70" y1="110" x2="80" y2="52" stroke-width="1" />
<line x1="80" y1="52" x2="90" y2="131" stroke-width="1" />
<line x1="90" y1="131" x2="100" y2="79" stroke-width="1" />
<line x1="100" y1="79" x2="110" y2="84" stroke-width="1" />
<line x1="110" y1="84" x2="120" y2="35" stroke-width="1" />
<line x1="120" y1="35" x2="130" y2="72" stroke-width="1" />
<line x1="130" y1="72" x2="140" y2="18" stroke-width="1" />
<line x1="140" y1="18" x2="150" y2="37" stroke-width="1" />
<line x1="150" y1="37" x2="160" y2="29" stroke-width="1" />
<line x1="160" y1="29" x2="170" y2="85" stroke-width="1" />
<line x1="170" y1="85" x2="180" y2="123" stroke-width="1" />
<line x1="180" y1="123" x2="190" y2="126" stroke-width="1" />
<line x1="190" y1="126" x2="200" y2="88" stroke-width="1" />
<line x1="200" y1="88" x2="210" y2="17" stroke-width="1" />
<line x1="210" y1="17" x2="220" y2="35" stroke-width="1" />
<line x1="220" y1="35" x2="230" y2="53" stroke-width="1" />
<line x1="230" y1="53" x2="240" y2="49" stroke-width="1" />
<line x1="240" y1="49" x2="250" y2="122" stroke-width="1" />
<line x1="250" y1="122" x2="260" y2="43" stroke-width="1" />
<line x1="260" y1="43" x2="270" y2="37" stroke-width="1" />
<line x1="270" y1="37" x2="280" y2="42" stroke-width="1" />
<line x1="280" y1="42" x2="290" y2="90" stroke-width="1" />
<line x1="290" y1="90" x2="300" y2="119" stroke-width="1" />
</g>
</svg>

AT_WebServer::_prepareHeader sendHeader Conn close
AT_WebServer::send1: write header =  HTTP/1.1 200 OK
Content-Type: image/svg+xml
Content-Length: 1949
Connection: close

---

2. MQTT_ThingStream on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield

The following are debug terminal output when running example MQTT_ThingStream on Adafruit SAMD51 ITSYBITSY_M4 and ESP8266-AT shield.

Start MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to SSID: HueNet1
You're connected to the network, IP = 192.168.2.62
SSID: HueNet1, Signal strength (RSSI): -43 dBm
***************************************
STM32_Pub
***************************************
Attempting MQTT connection to broker.emqx.io
...connected
Published connection message successfully!
Subscribed to: STM32_Sub
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message Send : STM32_Pub => Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
MQTT Message receive [STM32_Pub] Hello from MQTT_ThingStream on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library

---

3. MQTTClient_Auth on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield

The following are debug terminal output when running example MQTTClient_Auth on Adafruit SAMD51 ITSYBITSY_M4 and ESP8266-AT shield.

Starting MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to SSID: HueNet1
You're connected to the network, IP = 192.168.2.62
SSID: HueNet1, Signal strength (RSSI): -43 dBm
Attempting MQTT connection to broker.emqx.io...connected
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library

---

4. MQTTClient_Basic on Adafruit SAMD51 ITSYBITSY_M4 using ESP8266-AT shield

The following are debug terminal output when running example MQTTClient_Basic on Adafruit SAMD51 ITSYBITSY_M4 and ESP8266-AT shield.

MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to SSID: HueNet1
You're connected to the network, IP = 192.168.2.62
SSID: HueNet1, Signal strength (RSSI): -41 dBm
Attempting MQTT connection to broker.shiftr.io...connected
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Basic on ITSYBITSY_M4 with ESP8266-AT & ESP8266_AT_WebServer Library

---

5. WebClientRepeating on RASPBERRY_PI_PICO using ESP8266-AT shield

The following are debug terminal output when running example WebClientRepeating on RP2040-based RASPBERRY_PI_PICO and ESP8266-AT shield.

Starting WebClientRepeating on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to SSID: HueNet1
You're connected to the network, IP = 192.168.2.185
SSID: HueNet1, Signal strength (RSSI): -37 dBm

Connecting...
HTTP/1.1 200 OK
Server: nginx/1.4.2
Date: Tue, 11 May 2021 06:21:15 GMT
Content-Type: text/plain
Content-Length: 2263
Last-Modified: Wed, 02 Oct 2013 13:46:47 GMT
Connection: close
Vary: Accept-Encoding
ETag: "524c23c7-8d7"
Accept-Ranges: bytes


           `:;;;,`                      .:;;:.           
        .;;;;;;;;;;;`                :;;;;;;;;;;:     TM 
      `;;;;;;;;;;;;;;;`            :;;;;;;;;;;;;;;;      
     :;;;;;;;;;;;;;;;;;;         `;;;;;;;;;;;;;;;;;;     
    ;;;;;;;;;;;;;;;;;;;;;       .;;;;;;;;;;;;;;;;;;;;    
   ;;;;;;;;:`   `;;;;;;;;;     ,;;;;;;;;.`   .;;;;;;;;   
  .;;;;;;,         :;;;;;;;   .;;;;;;;          ;;;;;;;  
  ;;;;;;             ;;;;;;;  ;;;;;;,            ;;;;;;. 
 ,;;;;;               ;;;;;;.;;;;;;`              ;;;;;; 
 ;;;;;.                ;;;;;;;;;;;`      ```       ;;;;;`
 ;;;;;                  ;;;;;;;;;,       ;;;       .;;;;;
`;;;;:                  `;;;;;;;;        ;;;        ;;;;;
,;;;;`    `,,,,,,,,      ;;;;;;;      .,,;;;,,,     ;;;;;
:;;;;`    .;;;;;;;;       ;;;;;,      :;;;;;;;;     ;;;;;
:;;;;`    .;;;;;;;;      `;;;;;;      :;;;;;;;;     ;;;;;
.;;;;.                   ;;;;;;;.        ;;;        ;;;;;
 ;;;;;                  ;;;;;;;;;        ;;;        ;;;;;
 ;;;;;                 .;;;;;;;;;;       ;;;       ;;;;;,
 ;;;;;;               `;;;;;;;;;;;;                ;;;;; 
 `;;;;;,             .;;;;;; ;;;;;;;              ;;;;;; 
  ;;;;;;:           :;;;;;;.  ;;;;  ;;;;;;;`       .;;;;;;;,    ;;;;;;;;        ;;;;;;;:  
    ;;;;;;;;;:,:;;;;;;;;;:      ;;;;;;;;;;:,;;;;;;;;;;   
    `;;;;;;;;;;;;;;;;;;;.        ;;;;;;;;;;;;;;;;;;;;    
      ;;;;;;;;;;;;;;;;;           :;;;;;;;;;;;;;;;;:     
       ,;;;;;;;;;;;;;,              ;;;;;;;;;;;;;;       
         .;;;;;;;;;`                  ,;;;;;;;;:         
                                                         
                                                         
                                                         
                                                         
    ;;;   ;;;;;`  ;;;;:  .;;  ;; ,;;;;;, ;;. `;,  ;;;;   
    ;;;   ;;:;;;  ;;;;;; .;;  ;; ,;;;;;: ;;; `;, ;;;:;;  
   ,;:;   ;;  ;;  ;;  ;; .;;  ;;   ,;,   ;;;,`;, ;;  ;;  
   ;; ;:  ;;  ;;  ;;  ;; .;;  ;;   ,;,   ;;;;`;, ;;  ;;. 
   ;: ;;  ;;;;;:  ;;  ;; .;;  ;;   ,;,   ;;`;;;, ;;  ;;` 
  ,;;;;;  ;;`;;   ;;  ;; .;;  ;;   ,;,   ;; ;;;, ;;  ;;  
  ;;  ,;, ;; .;;  ;;;;;:  ;;;;;: ,;;;;;: ;;  ;;, ;;;;;;  
  ;;   ;; ;;  ;;` ;;;;.   `;;;:  ,;;;;;, ;;  ;;,  ;;;;   
3,CLOSED

---

6. MQTTClient_Auth on RASPBERRY_PI_PICO using ESP8266-AT shield

The following are debug terminal output when running example MQTTClient_Auth on RP2040-based RASPBERRY_PI_PICO and ESP8266-AT shield using Earle Philhower's arduino-pico core.

Starting MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to SSID: HueNet1
You're connected to the network, IP = 192.168.2.185
SSID: HueNet1, Signal strength (RSSI): -36 dBm
Attempting MQTT connection to broker.emqx.io...connected
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message Send : MQTT_Pub => Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
Message arrived [MQTT_Pub] Hello from MQTTClient_Auth on RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library

---

7. UdpNTPClient on MBED RASPBERRY_PI_PICO using ESP8266-AT shield

The following are debug terminal output when running example UdpNTPClient on RP2040-based MBED RASPBERRY_PI_PICO and ESP8266-AT shield using Arduino-mbed RP2040 core.

Starting UdpNTPClient on MBED RASPBERRY_PI_PICO with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to WPA SSID: HueNet1
You're connected to the network, IP = 192.168.2.76
UDP Packet received, size 48
From 132.163.96.1, port 123
Seconds since Jan 1 1900 = 3831340334
Unix time = 1622351534
The UTC time is 5:12:14
UDP Packet received, size 48
From 132.163.96.1, port 123
Seconds since Jan 1 1900 = 3831340344
Unix time = 1622351544
The UTC time is 5:12:24

---

8. AdvancedWebServer on NRF52840_ITSYBITSY

The following is debug terminal output when running example AdvancedServer on NRF52840_ITSYBITSY board, to demo how to send much larger data than total 2K of ESP8266/ESP32 AT-command shields

MULTIPLY_FACTOR = 4.0f

Starting AdvancedServer on NRF52840_ITSYBITSY with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Initializing ESP module
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to WPA SSID: HueNet1
[ESP_AT] Server started on port 80
HTTP server started @ 192.168.2.142, Port = 80
.[ESP_AT] New client 0
[ESP_AT] ESP8266_AT_Client::write: size =  84 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  84 , totalBytesSent = 84
[ESP_AT] ESP8266_AT_Client::write: Done, written =  84 , totalBytesSent = 84
[ESP_AT] ESP8266_AT_Client::write: size =  396 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  396 , totalBytesSent = 396
[ESP_AT] ESP8266_AT_Client::write: Done, written =  396 , totalBytesSent = 396
[ESP_AT] handleClient: Client disconnected
[ESP_AT] New client 0
[ESP_AT] String Len =  11219
[ESP_AT] ESP8266_AT_Client::write: size =  90 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  90 , totalBytesSent = 90
[ESP_AT] ESP8266_AT_Client::write: Done, written =  90 , totalBytesSent = 90
[ESP_AT] ESP8266_AT_Client::write: size =  11219 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 2048
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 9171
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 4096
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 7123
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 6144
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 5075
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 8192
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 3027
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 10240
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 979
[ESP_AT] ESP8266_AT_Client::write: written =  979 , totalBytesSent = 11219
[ESP_AT] ESP8266_AT_Client::write: Done, written =  979 , totalBytesSent = 11219
[ESP_AT] handleClient: Client disconnected
[ESP_AT] New client 0
[ESP_AT] ESP8266_AT_Client::write: size =  84 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  84 , totalBytesSent = 84
[ESP_AT] ESP8266_AT_Client::write: Done, written =  84 , totalBytesSent = 84
[ESP_AT] ESP8266_AT_Client::write: size =  396 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  396 , totalBytesSent = 396
[ESP_AT] ESP8266_AT_Client::write: Done, written =  396 , totalBytesSent = 396
[ESP_AT] handleClient: Client disconnected
[ESP_AT] New client 0
[ESP_AT] String Len =  11209
[ESP_AT] ESP8266_AT_Client::write: size =  90 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  90 , totalBytesSent = 90
[ESP_AT] ESP8266_AT_Client::write: Done, written =  90 , totalBytesSent = 90
[ESP_AT] ESP8266_AT_Client::write: size =  11209 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 2048
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 9161
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 4096
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 7113
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 6144
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 5065
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 8192
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 3017
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 10240
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 969
[ESP_AT] ESP8266_AT_Client::write: written =  969 , totalBytesSent = 11209
[ESP_AT] ESP8266_AT_Client::write: Done, written =  969 , totalBytesSent = 11209
[ESP_AT] handleClient: Client disconnected

---

9. ATWebServer_BigData on NRF52840_ITSYBITSY

The following is debug terminal output when running example ATWebServer_BigData on NRF52840_ITSYBITSY board, to demo how to send much larger data than total 2K of ESP8266/ESP32 AT-command shields

MULTIPLY_FACTOR = 3.0f

Start ATWebServer_BigData on NRF52840_ITSYBITSY with ESP8266-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Initializing ESP module
[ESP_AT] Use ES8266-AT Command
WiFi shield init done
Connecting to WPA SSID: HueNet1
[ESP_AT] Server started on port 80
HTTP server started @ 192.168.2.142, Port = 80
[ESP_AT] New client 0
String Len = 23106
[ESP_AT] ESP8266_AT_Client::write: size =  86 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  86 , totalBytesSent = 86
[ESP_AT] ESP8266_AT_Client::write: Done, written =  86 , totalBytesSent = 86
[ESP_AT] ESP8266_AT_Client::write: size =  23106 , MAX_SIZE = 2048
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 2048
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 21058
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 4096
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 19010
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 6144
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 16962
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 8192
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 14914
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 10240
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 12866
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 12288
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 10818
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 14336
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 8770
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 16384
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 6722
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 18432
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 4674
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 20480
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 2626
[ESP_AT] ESP8266_AT_Client::write: written =  2048 , totalBytesSent = 22528
[ESP_AT] ESP8266_AT_Client::write: Partially Done, written =  2048 , bytesRemaining = 578
[ESP_AT] ESP8266_AT_Client::write: written =  578 , totalBytesSent = 23106
[ESP_AT] ESP8266_AT_Client::write: Done, written =  578 , totalBytesSent = 23106
[ESP_AT] handleClient: Client disconnected

---

10. AdvancedWebServer on WIZNET_WIZFI360_EVB_PICO

The following is debug terminal output when running example AdvancedServer on WIZNET_WIZFI360_EVB_PICO board, using arduino-pico core

Starting AdvancedWebServer on WIZNET_WIZFI360_EVB_PICO with ESP32-AT & ESP8266_AT_WebServer Library
ESP8266_AT_WebServer v1.7.1
[ESP_AT] Using ESP32-AT Command
WiFi shield init done
Connecting to WPA SSID: HueNet
HTTP server started @ 192.168.2.124, Port = 80
.......... .......... .

---

---

Screen Shots

1. SAMD51 Itsy-Bitsy M4

This is the screen shot when running example AdvancedWebServer on Adafruit SAMD51 Itsy-Bitsy M4 board using this ESP8266_AT_WebServer Library

2. STM32 Nucleo-144 NUCLEO_F767ZI

This is the screen shot when running example AdvancedWebServer_STM32 on STM32 Nucleo-144 NUCLEO_F767ZI board using this ESP8266_AT_WebServer Library

3. nRF52 Itsy-Bitsy nRF52840

This is the screen shot when running example AdvancedWebServer on Adadruit nRF52840 Itsy-Bitsy board using this ESP8266_AT_WebServer Library

4. Seeeduino SEEED_XIAO_M0

This is the screen shot when running an example using UDP Multicast on Seeeduino SEEED_XIAO_M0 board using this ESP8266_AT_WebServer Library. The UDP MUlticast is used to manage Internet Gateway's Port Forwarding so that we can access from WAN, port 5990, the WebServer running in LAN, port 5990.

5. RASPBERRY_PI_PICO

This is the screen shot when running example AdvancedWebServer on RASPBERRY_PI_PICO board using this ESP8266_AT_WebServer Library

6. MBED RASPBERRY_PI_PICO

This is the screen shot when running example AdvancedWebServer on MBED RASPBERRY_PI_PICO board using this ESP8266_AT_WebServer Library

7. nRF52 Itsy-Bitsy nRF52840 BigData

This is the screen shot when running example AdvancedWebServer on Adadruit nRF52840 Itsy-Bitsy board using this ESP8266_AT_WebServer Library sending BigData

---

---

Debug

Debug is enabled by default on Serial. Debug Level from 0 to 4. To disable, change the WIFI_LOGLEVEL and WIFININA_LOGLEVEL to 0

// Use this to output debug msgs to Serial
#define DEBUG_ESP8266_AT_WEBSERVER_PORT   Serial

// Debug Level from 0 to 4
#define _ESP_AT_LOGLEVEL_                 1

---

Troubleshooting

If you get compilation errors, more often than not, you may need to install a newer version of the board's core, applying Libraries' Patches, Packages' Patches or this library latest version.

---

---

Issues

Submit issues to: ESP8266_AT_WebServer issues

---

---

TO DO

1. Bug Searching and Killing
2. Add SSL/TLS Client and Server support
3. Support more types of boards using ESP8266 AT-command shields.
4. Add mDNS features.

DONE

1. Add support to Arduino SAMD21 (ZERO, MKR, NANO_33_IOT, etc.)
2. Add support to Adafruit SAMD21 (Itsy-Bitsy M0, Metro M0, Feather M0 Express, etc.).
3. Add support to Adafruit SAMD51 (Itsy-Bitsy M4, Metro M4, Grand Central M4, Feather M4 Express, etc.).
4. Add support to Adafruit nRF52 ( Feather nRF52832, nRF52840 Express, BlueFruit Sense, Itsy-Bitsy nRF52840 Express, Metro nRF52840 Express, NINA_B302_ublox, NINA_B112_ublox, etc.).
5. Add support to SAM DUE.
6. Add support to ESP32-AT
7. Add support to W600 and WIS600-01S
8. Add support to all STM32F/L/H/G/WB/MP1
9. Add support to Seeeduino SAMD21/SAMD51 boards (SEEED_WIO_TERMINAL, SEEED_FEMTO_M0, SEEED_XIAO_M0, Wio_Lite_MG126, WIO_GPS_BOARD, SEEEDUINO_ZERO, SEEEDUINO_LORAWAN, SEEED_GROVE_UI_WIRELESS, etc.)
10. Add UDP Multicast feature.
11. Add PROGMEM and FlashString related commands such as sendContent_P() and send_P(), and use in examples.
12. Clean-up all compiler warnings possible.
13. Add Version String
14. Add Table of Contents
15. Add support to SIPEED_MAIX_DUINO
16. Add support to Arduino Nano RP2040 Connect using Arduino mbed OS for Nano boards.
17. Add support to RP2040-based boards, such as RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040 and GENERIC_RP2040, using Earle Philhower's arduino-pico core.
18. Add support to RP2040-based boards, such as RASPBERRY_PI_PICO, ADAFRUIT_FEATHER_RP2040 and GENERIC_RP2040, using Arduino-mbed RP2040 core
19. Reduce usage of Arduino String with std::string
20. Optimize library code and examples by using reference-passing instead of value-passing.
21. Fix severe limitation to permit sending larger data than 2K buffer of ESP8266/ESP32 AT-command shields
22. Add example ATWebServer_BigData to demo how to send larger data than 2K buffer
23. Modify example AdvancedWebServer to demo how to send larger data than 2K buffer
24. Add support to WizNet WizFi360, such as WIZNET_WIZFI360_EVB_PICO using arduino-pico core

---

---

Contributions and Thanks

1. Based on and modified Ivan Grokhotkov's ESP8266WebServer
2. Based on and modified from bportaluri's WiFiEsp library
3. Thanks to good work of Miguel Alexandre Wisintainer for initiating, inspriring, working with, developing, debugging and testing. Without that, support to nRF52, especially U-Blox B302 running as nRF52840 and U-Blox B112 running as nRF52832, has never been started and finished. Also see U-BLOX NINA B302/ENC28J60 with Alexa/SinricPro.
4. Thanks to reltkaine to report the compile error issue with Sipeed Maixduino core, leading to v1.4.1 to introduce Packages_Patches for Sipeed Maixduino core

⭐️⭐️ Ivan Grokhotkov

⭐️ Bruno

⭐️ Miguel Wisintainer

reltkaine

---

Contributing

If you want to contribute to this project:

• Report bugs and errors
• Ask for enhancements
• Create issues and pull requests
• Tell other people about this library

---

License

• The library is licensed under MIT

---

Copyright

Copyright (C) 2020- Khoi Hoang