The original GRBL Project is located at : http://github.com/grbl/grbl this project is a fork specialized in punch machines as below. It has a X and Y axis plus a punch command for punching holes in the barrel organ book.
This GRBL project has a gui for handling the punch plan, and grbl control using a PC, Mac or Linux. please see the associated software website : www.barrel-organ-discovery.org
Punch machine designed and constructed by Jean Pierre Rosset.
This patch add a new M100 GCode command designed for punching machines. This new punching M100 command handle the punch cycle. This command permit to wire the punch actuators and sensor and use them in a GCode program
The punch cycle introducted is the following
- activate the punch down actuator
- wait for the punch to be on bottom (wait the activation of the punchdown sensor)
- activate the punch up actuator
- wait for the punch to be up
at least you must have two sensors for the punch positions (up and down). the activation of the up actuator is optional as some punch actuator, once desactivated, move up the punch.
Only Arduino Uno CPU is supported yet in this version.
In the adjustment of grbl software :
- The spindle is disconnected, and the pins are reuse for punching
- The D12 and D13 are now used for handling the actuators for the punch
- The A4 and A5 pins for detecting the state of the punch (up or down)
All other pins are remained the same.
https://www.youtube.com/watch?v=Sks70Pnujw8
the Easiest way to install the software is to use the XLoader software
you can download this software at this url http://russemotto.com/xloader/
Launch XLoader
Upload the grblPunch.hex file,
Warning : please download the hole project as a zip file, and take the grblPunch.hex file from it. Using internet Explorer to save the file as a text file can corrupt the file.
That's all
You can then use the universal code sender to connect and configure the elements.
Additional settings are introducted in this version of grbl, $30, $31, $32, $33 for adjusting the behaviour of the punch cycle, depending on the actuator and sensors used.
>>>> $30=0 (punch actuator down invert, bool)
>>>> $31=0 (punch actuator up invert, bool)
>>>> $32=1 (punch sensor down invert, bool)
>>>> $33=1 (punch sensor up invert, bool)
the $32 and $33 settings permit to invert the detection of the punch position.
| setting | value | description |
|---|---|---|
| $30 | 0 | The punch down actuator is activated if the PIN is at "5v" |
| $30 | 1 | The punch down actuator is activated if the PIN is at "0v" |
| $31 | 0 | The punch up actuator is activated if the PIN is at "5v" |
| $31 | 1 | The punch up actuator is activated if the PIN is at "0v" |
| $32 | 0 | The punch down is detected down if the sensor is "0v" |
| $32 | 1 | The punch down is detected down if the sensor is "5v" |
| $33 | 0 | The punch up is detected up if the sensor is "0v" |
| $33 | 1 | The punch up is detected up if the sensor is "5v" |
you can view the associated parameters in launching the $$ command
$$
$0=10 (step pulse, usec)
$1=25 (step idle delay, msec)
$2=0 (step port invert mask:00000000)
$3=0 (dir port invert mask:00000000)
$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=3 (status report mask:00000011)
$11=0.010 (junction deviation, mm)
$12=0.002 (arc tolerance, mm)
$13=0 (report inches, bool)
$20=0 (soft limits, bool)
$21=0 (hard limits, bool)
$22=0 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=25.000 (homing feed, mm/min)
$25=500.000 (homing seek, mm/min)
$26=250 (homing debounce, msec)
$27=1.000 (homing pull-off, mm)
>>>> $30=0 (punch actuator down invert, bool)
>>>> $31=0 (punch actuator up invert, bool)
>>>> $32=0 (punch sensor down invert, bool)
>>>> $33=0 (punch sensor up invert, bool)
$100=250.000 (x, step/mm)
$101=250.000 (y, step/mm)
$102=250.000 (z, step/mm)
$110=500.000 (x max rate, mm/min)
$111=500.000 (y max rate, mm/min)
$112=500.000 (z max rate, mm/min)
$120=10.000 (x accel, mm/sec^2)
$121=10.000 (y accel, mm/sec^2)
$122=10.000 (z accel, mm/sec^2)
$130=200.000 (x max travel, mm)
$131=200.000 (y max travel, mm)
$132=200.000 (z max travel, mm)
you can change a setting value using
$33=1
2016 - February
- fix sensor detection, additional material has been setted up, we still need 2 sensors for the punch (eliminating the time in the equation)
2015 - November
by settings,- able to use a "pull up" logic on the hard limit
or use two 0-1 detector on both side of the X axis
2015 - November
- Validation of the master branch with a real machine
Todo
- Check at startup that the punch is up, before starting (part of the homing cycle checks)